Search results for "coverter auto26"
supports a lot of SH2, SH3 and SH4 derivatives from Renesas includes software for Windows, Linux and MacOSX requires Power Debug Module debug cable with 14 pin connector Targets with 36 pin Hirose connector require the converter LA-7980 for ST40 targets please request debug cable with 20 pin connector
supports Qorivva MPC5xxx/SPC5xxx (e200 cores) and Freescale PX SERIES processors eTPU, GTM and SPT debugging included Concurrent debugging of multiple e200 cores on multicore processors requires a License for Multicore Debugging (LA-7960X) (not necessary for lockstep mode) includes software for Windows, Linux and MacOSX requires Power Debug Interface USB 2.0/USB 3.0, Power Debug Ethernet, Power Trace Ethernet, Power Debug II, PowerDebug PRO or PowerDebug E40 includes LA-3873 (Conv. AUTO26 to JTAG14 OnCE)
Converter from Intel MIPI60-Cv2 to MIPI34 pin-out on target Converts termination scheme Intel (50 Ohm parallel termination at receiver) to termination scheme ARM (50 Ohm series termination at sender) Support for JTAG/SWD Maps Intel specific debug signals to MIPI34 pins. Default mapping: Intel PREQ -> DBGREQ (pin 18 on MIPI34) Intel PRDY -> DBGACK (pin 20 on MIPI34) Intel HOOK6 (PMODE) -> RTCK (pin 12 on MIPI34) Intel HOOK0 (PowerGood) -> BCE (pin 14 on MIPI34) Intel HOOK7 (ResetOut) -> RESET (pin 10 on MIPI34) TVREF (trace reference voltage) == DVREF (debug reference voltage) For other possible options, please contact Lauterbach.
Trace recorder for serial high-speed ports with 8 Gigabyte trace memory for MPC57xx/SPC5xx Records up to 8 lanes with 12.5 Gbit/s per lane (more with opt. Prepro.) Voltage range: 0.15 to 1.25 differential voltage. For Samtec34 target connector add LA-3871: Converter Samtec40 HSTP+AUTO26+JTAG14 to Samtec34 including Samtec 34-pin flex extension cable For Samtec22 target connector add LA-3872: Converter Samtec40 HSTP+AUTO26+JTAG14 to Samtec22 including Samtec 22-pin flex extension cable Requires PowerDebug X50, PowerDebug PRO, or PowerDebug II. Requires PC with USB 3 or Gigabit Ethernet, 4 GB RAM min, and 64-bit OS.
Serial Trace Port Controller with 4 Giga Byte Trace Memory for QorIQ PowerPC converters for Samtec22 or Samtec46 have to be ordered separately if required requires PowerDebug II Ethernet or PowerDebug PRO Host requirements: USB 3.0 or 1000 MBit Ethernet interface, 4.0 GigaByte RAM voltage range 0.15V to 1.25V
Supports off-chip RAM trace port for of TI chips if applied to an AUTOFOCUS II preprocessor please add the serial number of the preprocessor to your order AUTOFOCUS II Preprocessors with serial number C0806xxxxxx and lower have to be send to Lauterbach Germany for an hardware upgrade May require LA-3835 Converter Mictor38/ETM+IDC20A to Mictor-38/RTP
JTAG only converter from Mictor76, Mictor38, Samtec50, Samtec20 or JTAG14 to Mictor38, Samtec50, Samtec20 or JTAG14. Not all connectors can be mounted at the same time. Please refer to https://www.lauterbach.com/support/static/LA-7640.pdf Connector types for top and bottom side must be ordered explicitly!
Probe to record analog signals from a 20 pin IDC connector: 4 Channels 0..5 V 12 Bit Resolution, 3 Current Sense Channels, Conversion Rate 625K Samples/Sec. The probe requires one of the following modules. PowerIntegrator (LA-7940), PowerIntegrator II (LA-3940/3941/3942), PowerTrace II (LA-7692/7693/7694), PowerTrace Serial (LA-3120/3520/3555/3560). CombiProbe (LA-4502), CombiProbe 2 (LA-3060) and MicroTrace (LA-3050). For CombiProbe, CombiProbe 2 and MicroTrace the converter LA-4508 is required. For CombiProbe 2 and MicroTrace we recommend to use the Mixed-Signal Probe (LA-2500) instead of this analog probe. The probe is not suitable for PowerTrace III (LA-2520/2521), PowerTrace II Lite (LA-3580/3581), PowerTrace Serial 2 (LA-3121/3122). For those devices, you can use the Mixed-Signal Probe (LA-2500) instead (except for PowerTrace II Lite). Includes a 20 pin male-male adaptor.
Preprocessor for AUD Real-Time Trace for SH2A, SH4 and SH4A cores 550 MHz clock speed Variable threshold level and termination voltage, AUTOFOCUS self calibration technology, Supports 1.2 to 3.3V - else contact support Requires PowerTrace Version 6 or higher or PowerTrace II / III Requires converter LA-7819 for 14 pin debug cables voltage range 1.2V to 3.3V
Preprocessor for RAM Trace Port on TI chips 500 MHz clock speed Variable threshold level and termination voltage, AUTOFOCUS self calibration technology, Supports 1.2 to 3.3V - else contact support Requires PowerTrace Version 6 or higher or PowerTrace II / III May require LA-3835 Converter Mictor38/ETM+IDC20A to Mictor-38/RTP voltage range 1.2V to 3.3V