Search results for "a20"
supports NEC V850 with N-Wire includes software for Windows, Linux and MacOSX requires Power Debug Interface USB 2.0/USB 3.0, Power Debug Ethernet, Power Debug II or PowerDebug PRO debug cable with 20 pin connector requires LA-7936 if KEL connector is used on the target requires LA-7937 if Mictor connector is used on the target
Converter from 14 Pin JTAG/OnCE MPC5XXX to AUTO26/20/10 use with LA-7753 JTAG Debugger Qorivva MPC5xxx/SPC5xxx (ICD) to connect to targets designed for LA-2708 (Debugger for MPC5xxx Automotive PRO) LA-3206 Debugger for MPC5xxx AUTO26 (PACK) LA-3736 (JTAG Debugger for MPC5xxx Automotive)
supports Arm11 (0.4 V - 5 V) IDC20A debug cable supports 5-pin standard JTAG, cJTAG and Serial Wire Debug Port, (0.4 V - 5 V) includes software for Windows, Linux and MacOSX requires Power Debug Module cJTAG and SWD require Power Debug Interface USB 2.0/USB 3.0, Power Debug Ethernet, PowerTrace, Power Debug II or PowerDebug PRO
Preprocessor for RAM Trace Port on TI chips 500 MHz clock speed Variable threshold level and termination voltage, AUTOFOCUS self calibration technology, Supports 1.2 to 3.3V - else contact support Requires PowerTrace Version 6 or higher or PowerTrace II / III May require LA-3835 Converter Mictor38/ETM+IDC20A to Mictor-38/RTP voltage range 1.2V to 3.3V
supports Arm9 (0.4 V - 5 V) IDC20A debug cable supports 5-pin standard JTAG, cJTAG and Serial Wire Debug Port, (0.4 V - 5 V) includes software for Windows, Linux and MacOSX requires Power Debug Module cJTAG and SWD require Power Debug Interface USB 2.0/USB 3.0, Power Debug Ethernet, PowerTrace, Power Debug II or PowerDebug PRO
Supports Arm Cortex-M cores trace support ETM Cortex-M via ETB included IDC20A debug cable supports 5-pin standard JTAG, cJTAG and Serial Wire Debug Port, (0.4 V - 5 V) includes software for Windows, Linux and MacOSX requires Power Debug Module cJTAG and SWD require Power Debug Interface USB 2.0/USB 3.0, Power Debug Ethernet, PowerTrace, Power Debug II or PowerDebug PRO
Probe to record analog signals from a 20 pin IDC connector: 4 Channels 0..5 V 12 Bit Resolution, 3 Current Sense Channels, Conversion Rate 625K Samples/Sec. The probe requires one of the following modules. PowerIntegrator (LA-7940), PowerIntegrator II (LA-3940/3941/3942), PowerTrace II (LA-7692/7693/7694), PowerTrace Serial (LA-3120/3520/3555/3560). CombiProbe (LA-4502), CombiProbe 2 (LA-3060) and MicroTrace (LA-3050). For CombiProbe, CombiProbe 2 and MicroTrace the converter LA-4508 is required. For CombiProbe 2 and MicroTrace we recommend to use the Mixed-Signal Probe (LA-2500) instead of this analog probe. The probe is not suitable for PowerTrace III (LA-2520/2521), PowerTrace II Lite (LA-3580/3581), PowerTrace Serial 2 (LA-3121/3122). For those devices, you can use the Mixed-Signal Probe (LA-2500) instead (except for PowerTrace II Lite). Includes a 20 pin male-male adaptor.
AUTO26 Whisker for CombiProbe suitable for TriCore and dsPIC with 26-pin automotive connector, supporting DAP (DAP2, DAP3, DAP4, DAPWide), JTAG, DXCPL/DXCM. For optimal performance, we recommend using a DAP mode. DAP streaming is supported for TriCore (in DAP mode) and works most effectively with DAPWide (up to 320 Mbit/s). For DXCPL/DXCM, you will likely require the CAN-Box (LA-3889) as well. Voltage Range: 1.8V to 5.0V. Debug Clock Frequency: 10 kHz to 160 MHz Target Connector: AUTO26, AUTO20, AUTO10 Requires a CombiProbe or CombiProbe 2. For dsPIC only JTAG is supported and the converter LA-2773 to the 8-pin Microchip connector is recommended. Please note that TriCore SoCs usually support only 3.3V or 5V in DAP mode. Debug clock frequency in JTAG mode is typically limited to 40 MHz on TriCore SoCs (while up to 160 MHz is supported in DAP mode).
Supports Armv8-A/R or Armv9-A/R based Cortex-A and Cortex-R 32/64-bit cores IDC20A debug cable supports 5-pin standard JTAG, cJTAG and Serial Wire Debug Port, (0.4 V - 5 V) Multicore debugging included includes software for Windows, Linux and MacOSX requires Power Debug Module cJTAG and SWD require Power Debug Interface USB 2.0/USB 3.0, Power Debug Ethernet, PowerTrace, Power Debug II or PowerDebug PRO
Converter from Intel MIPI60-Cv2 to MIPI34 pin-out on target Converts termination scheme Intel (50 Ohm parallel termination at receiver) to termination scheme ARM (50 Ohm series termination at sender) Support for JTAG/SWD Maps Intel specific debug signals to MIPI34 pins. Default mapping: Intel PREQ -> DBGREQ (pin 18 on MIPI34) Intel PRDY -> DBGACK (pin 20 on MIPI34) Intel HOOK6 (PMODE) -> RTCK (pin 12 on MIPI34) Intel HOOK0 (PowerGood) -> BCE (pin 14 on MIPI34) Intel HOOK7 (ResetOut) -> RESET (pin 10 on MIPI34) TVREF (trace reference voltage) == DVREF (debug reference voltage) For other possible options, please contact Lauterbach.